Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Bushwick Homeowners
Water is what kills chimneys in Bushwick, and it almost always gets in at the top. A cracked crown or a missing cap lets rain run straight down the flue, soak the masonry, and freeze in February. By the time a homeowner notices a stain on the ceiling, the damage has been working for a while. We’ve seen it across the neighborhood’s older rowhouses, where the original crowns have been sitting up there for generations and the caps were never replaced. Our technicians have up to 10 years of experience with cap and crown work, and from inspection to repair, it’s handled by the same specialist crew. We diagnose before we recommend. If the crown is sound, we’ll tell you so. If it needs work, you’ll see the photos. Same-day service is available in Bushwick. Call (855) 337-1157.
What Our Chimney Cap & Crown Service Includes
Every part of the chimney top is part of one system, and we treat it that way. Here’s what each piece of the work actually involves.
Cap Installation
A cap is the cover that sits on top of the flue, keeping rain, snow, birds, and squirrels out while letting smoke escape. If your chimney has an open flue with nothing over it, a cap is the single most effective thing you can add to stop water damage. We size the cap to the flue opening and the appliance, then anchor it so winter wind doesn’t shift it. Most caps we install are Famco or Olympia Chimney models chosen for the flue type and the draft your fireplace or stove needs.

Cap Replacement
Caps rust through, crack, or blow loose in a storm, and a damaged cap is worse than no cap because it funnels water instead of shedding it. If yours is bent, sitting crooked, or missing a section of mesh, it needs replacing rather than patching. We match the new cap to the same flue opening, check that the old one didn’t scratch the flue tile on its way down, and haul the old cap away.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that slopes water away from the flue. When hairline cracks spread across it, water seeps into the brick below and starts spalling the face. We repair crowns that are still structurally sound by cutting out the cracked section, re-forming the slope, and bonding new material to the old. If the crown has separated from the brick entirely, we’ll show you the gap and explain the rebuild.

Crown Coating
Crown coating is a flexible protective layer applied over a crown that’s intact but no longer shedding water well. It’s a good option when the crown has fine surface checking but no structural failure, because it seals those small cracks before they widen. We use HeatShield crown coating, which flexes with the masonry instead of cracking away from it the way a thin paint-on sealer does. Coating buys years on a crown that would otherwise need rebuilding.
Multi-Flue Cap
Bushwick rowhouses often have two or three flues side by side in one stack, serving a fireplace, a furnace, and sometimes a water heater. A multi-flue cap covers the whole stack with one unit, protecting every flue at once and cutting down on the number of independent pieces that can fail. We measure the full stack, confirm the flues are at compatible heights, and set a single top-mount cap with mesh on all sides. This is usually cleaner-looking and more durable than three individual caps chasing each other around the same crown.
Custom Cap
Some chimneys don’t fit a standard cap: oversize flues, unusual stack shapes, or a cap that has to clear a specific appliance’s draft requirement. In those cases we order a custom cap built to your dimensions. That might mean a taller mesh section on a wood-burning flue, or a lower-profile cap where the crown space is tight. Nothing gets forced to fit.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with a small, vetted set of professional-grade brands because cap and crown work fails when the material is wrong. Olympia Chimney caps are one we know well; their multi-flue units are built for the kind of stack you see on Bushwick rowhouses, and we know how their mounting hardware holds up through freeze-thaw cycles. Famco is the other cap name you’ll see us work with most, and we’ve handled enough of their venting and structural components to know where the weak points show up first.
When a crown needs rebuilding rather than patching, HeatShield is the material system we reach for, because it’s made to flex with masonry rather than crack away from it. DuraFlex enters the picture when a failed crown has let water into the flue liner and the liner needs relining too. We service these brands and understand how each one behaves in this climate. Whether you have Olympia Chimney, Famco, HeatShield, DuraFlex, or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water stains on the ceiling or chimney breast. A dark ring near the chimney usually means water is getting past the crown or cap and running down the masonry. Catch it early and it’s a cap or crown job; ignore it and it becomes a flue liner replacement.
- Crumbling mortar or flaking brick just below the roofline. When the brick near the top starts spalling, water is soaking in and freezing. That freeze-thaw cycle pops the face off the brick, and it only accelerates once it starts.
- A cap that’s crooked, rusted, or missing its mesh. A leaning cap no longer sheds water where it should, and missing mesh means birds and squirrels can nest in the flue. Both are straightforward cap replacements.
- Visible cracks in the crown, or the crown pulling away from the brick. A hairline crack can be coated. A crown with a real gap between it and the brick is a structural issue that needs repair before the next hard freeze.
- Draft problems or smoke backing into the room. Sometimes a cap that’s the wrong height or blocked mesh is the cause, not the fireplace itself. Before anyone sells you fireplace work, the top of the chimney should be checked.
Our Chimney Cap & Crown Process – Step by Step
- 1
Inspection first. We start with a camera inspection of the flue and a close look at the crown, cap, and top courses of brick. You get a photo report of what we find, so you’re looking at the same thing we are. Nothing gets recommended before you’ve seen the evidence.
- 2
Diagnosis and written estimate. We tell you what’s failed, what’s holding, and what can safely wait. The estimate is written and the price is per job. If the crown only needs coating and you were expecting a rebuild, you’ll hear that from us.
- 3
Material selection. For caps, we match the model to your flue count and appliance type, drawing on Olympia Chimney and Famco options. For crowns, we choose between repair, coating, or rebuild based on how much sound material is left. You’ll know which material we’re using and why.
- 4
The work. We protect the roof surface, set up safely, and do the cap or crown work in one visit where conditions allow. Crown repairs get re-sloped so water actually runs off, not just sealed flat.
- 5
Final check and photo record. We confirm the cap is seated and the crown sheds water, then send you the after photos alongside the before shots. You’ll have a record of the work for your own files.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Bushwick?
A single-flue cap installation in Bushwick typically runs $250 – $550 installed, depending on the cap model and how accessible the chimney top is. A multi-flue cap for a two or three-flue rowhouse stack usually lands between $450 – $850, since the unit is larger and the mounting is more involved. Crown coating runs roughly $350 – $650 for a standard crown, while a crown repair with re-sloping typically falls in the $600 – $1,200 range. A full crown rebuild on a deteriorated stack is a bigger job, generally $1,200 – $2,500, and it’s the one we’re most careful about recommending only when the photos support it.
What moves the price: the number of flues, the height and pitch of the roof, whether the crown has failed structurally or just at the surface, and whether water has already reached the liner. That last factor is the one people don’t see coming. A failed crown that’s let water into the flue can turn a crown job into a relining job, which is why we inspect the flue before quoting the top.
How to avoid overpaying: ask to see the photos, ask whether the crown can be coated instead of rebuilt, and ask what happens if you wait a season. Sometimes the honest answer is that it can wait. Our estimates are free and written, and the price is set per job, so there’s no surprise line item later.
Chimney Cap & Crown Near Bushwick – Our Service Area
We work across Bushwick and the neighborhoods around it: Williamsburg, Greenpoint, Bedford-Stuyvesant, Clinton Hill, Fort Greene, Crown Heights, Prospect Heights, Brownsville, and over into Ridgewood, Maspeth, and Glendale in Queens. Roof access and stack styles differ block to block, and we plan each visit around what the building actually looks like. If you’re comparing options nearby, our chimney cap & crown page covers the rowhouse stacks common over there, and the same crew handles both. Fast dispatch runs 7am to 7pm, Sunday through Friday.
Serving Bushwick, NY – Our Local Coverage Area
We serve Bushwick and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Bushwick
Chimney cap and crown service covers the two parts at the very top of your chimney that keep water out: the cap that covers the flue opening, and the crown, the sloped slab of concrete or mortar that sheds rain off the brick below. The cap stops water and animals from entering the flue directly, while the crown protects the masonry itself. Together they’re the first line of defense against the water damage that causes most long-term chimney deterioration. We handle installation, replacement, repair, coating, multi-flue units, and custom caps. Call (855) 337-1157 for an exact quote; estimates are free.
Most cap installations and crown coatings are completed in a single visit, usually a few hours depending on roof access. A crown repair with re-sloping can take a bit longer, and a full crown rebuild may need more than one visit if the material has to cure. We’ll tell you the expected timeline in the written estimate so you can plan around it. Weather matters too, since crown material doesn’t like to be applied in rain or freezing temperatures.
Typical estimates in Bushwick run from about $250 – $550 for a single-flue cap, $450 – $850 for a multi-flue cap, $350 – $650 for crown coating, and $600 – $1,200 for crown repair. A full crown rebuild is generally $1,200 – $2,500 depending on the stack. The final price depends on flue count, roof access, and how far the damage has gone. Every estimate is free, written, and set per job. Call (855) 337-1157 for an exact quote.
Yes. We service Olympia Chimney and Famco caps and venting components, and we know where each tends to wear first. If your existing cap needs replacing rather than repairing, we’ll match the new unit to your flue opening and appliance so the draft stays right. Whether you have Olympia Chimney, Famco, or another make, we can help.
Same-day service is available in Bushwick when the schedule allows. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday; a call outside dispatch hours is booked into the next opening. If a cap has blown off in a storm, call and we’ll get you on the schedule. We don’t promise a same-day slot until we’ve confirmed it.
Our work is backed by a satisfaction guarantee, and we stand behind the installation itself. If something we installed isn’t seated or sealed correctly, we’ll come back and make it right. The specific warranty terms for the materials come from the manufacturer, and we’ll explain those in writing before the job starts. Ask us about it during the estimate.
Clear access to the chimney, both inside and out, and make sure someone is home to let the technician in. If the chimney is behind furniture or a closet panel, moving that ahead of time saves time. We handle the roof protection and the work itself, and we’ll walk you through the photos at the end. Beyond access, there’s nothing you need to do.
Schedule Your Chimney Cap & Crown Service in Bushwick Today
If your cap is missing, leaning, or the crown has cracks you can see from the ground, it’s worth a look before the next freeze. We inspect first, show you the photos, and recommend only what the evidence supports. Our Chimney Sweep Bushwick team handles cap and crown work across Bushwick and nearby neighborhoods, including chimney cap & crown jobs in Ridgewood. Call (855) 337-1157 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Bushwick.